Cold Welding CompoundsCold Welding Compounds





Speciality CompoundsSpeciality Coatings and Sealants





Metal TreatmentMetal Treatment Chemicals





Flooring SolutionsFlooring Solutions : Sealers and Toppings





Selection GuideSpecification Guide with Important Tips





Application TipsApplication Guide





Application AreasApplication Area and Case Studies






Email us
Speciality compounds used for coating and / or sealing


Fo-Poxy (Magic Putty)
A 2-in-1 high performance, 5 minutes set putty

A high performance, quick set, 2-in-1 epoxy stick which drastically cuts down shutdown time. Simply cut, knead and apply on the leak or rebuild area. Sets within a very short time and can be further strengthened by applying Fo-Poxy (S) Cold Weld Compound over it.


Fo-Poxy (SP)
Anti Corrosive and Wear Resistant coating.

 It has an excellent chemical resistance against Solvents, Acids, Alkalis and petro-chemicals. Can be used as a coating over ferrous / non-ferrous structures, piping, pump casings, pump beds, joints, interior and exterior tank lining, etc. Can also be successfully used for atmospheric corrosion protection and wear resistance coating, also as a replacement of Teflon in areas such as bagging units.


Fo-Poxy (SP 2)
Rubber or Brick lining repair/replacement compound

Fo-Poxy (SP 2) can be applied as a coating over M.S., C.I., S.S., etc. for protection against corrosive chemicals. Storage tank, filters, centrifuge, agitators coated with Fo-Poxy (SP 2) will give a much longer life as compared to rubber/brick lining. Fo-Poxy (SP 2) can also be used to repair existing rubber lining cracks that help to reduce further peeling and damage to MS Tank lining.


Fo-Poxy (C)(L)
Low Viscosity Ceramic compound

Low Viscosity Ceramic compound for providing wear and abrasion resistant coating or lining


Fo-Poxy (U)
2 component Polyurethane repairing system

Brushable PU system for conveyor belt repairs and for flexible coating / lining.


Fo-Poxy (U1)
PU putty for Rubber repairs

Polyurethane Putty for rebuilding rubber parts viz conveyor belts, tyres, etc. and impact resistant lining.


Fo-Poxy (UE)
Brushable Flexible Epoxy as coating / lining

A 2-pack, flexible epoxy system used as an anti-corrosive coating or lining for water tank in boiler feed system & preventive treatment of mild steel pipe fittings. Can be also used for repair of rubber parts or in casting of rubber-like parts. It is an ideal solution in providing an impact, abrasion and corrosion / erosion resistant coating / flooring. It is also used to provide insulation repair for trailing and control cables.


Fo-Poxy (Alicoat)
Brushable Aliphatic Polyurethane coating

Brushable Aliphatic Polyurethane coating for exterior structural coating or waterproofing.


Fo-Poxy (aqua seal)
A general 2-part epoxy sealant.

For sealing, patching and repairing pipes, fittings, vessel, tanks or equipment leakages.


Fo-Poxy (Kit)
A Complete Maintenance Kit.

 Includes Cold Weld machinable and emergency repair grades, Reinforcement tape roll for added strength, Cynoacrylate based quick set solution and Cleaner and conditioner solution.


Fo-Poxy (UV)
UV curable, tranparent, 1-part adhesive coating.

Cures in 2 to 3 minutes under UV-A light (100mw/cm to the power of 2 minimum power recommended). Used for Glass- to -Glass Bonding, Printed Circuit Boards, Acrylic bonding, etc.


Fo-Poxy (UW)
An under-water curable 2-part epoxy sealant.

For sealing, patching pipes, fittings or concrete block leakages which may be submerged under water.


NOTE :

We can also develop Fo-Poxy as per client requirements.


Inquiries    |    Mail Us